|
Mordel's Bar & Grill |
|
|
» |
View previous topic :: View next topic |
Author |
Message |
Toxic_Toast Free Worlds League Sergeant
Joined: 25-Aug-2023 21:49 Posts: 99 Location: United States
|
Posted: 04-Dec-2023 16:43 Post subject: Catherine CTE-1A |
|
|
TRO: Catherine CTE-1A | BattleMech Technical Readout
Name/Model: Catherine CTE-1A
Designer: Toxic_Toast
Source(s): Custom Mordel.Net Units
Technology: Inner Sphere
Technology Rating: E
Tonnage: 45
Role: Skirmisher
Configuration: Biped BattleMech
Era/Year: Dark Age / 3150
Rules (Current): Standard
Rules (Era): Standard
Rules (Year): Standard
Total Cost: 8,380,565 C-Bills
Battle Value: 1,340
Chassis: Endo Steel
Power Plant: 270 XL
Walking Speed: 64.8 kph
Maximum Speed: 97.2 kph
Jump Jets: Standard
Jump Capacity: 150 meters
Armor: Light Ferro-Fibrous with CASE II
Armament:
1 Large X-Pulse Laser
1 LRM 10
1 ER Medium Laser
1 Small X-Pulse Laser
Manufacturer: Unknown
Primary Factory: Unknown
Communications: Unknown
Targeting & Tracking: Unknown
================================================================================================
Overview:
Description: The story of the Catherine would begin with the end the Liberator Mech
experiment under Kali Yama and the FWL. With its legendary 3018 performance condemning the
Liberator's future Kali-Yama would archive the design. It would languish in records until
3089 when the design would be purchased by Grumman Amalgamated for a pittance. Grumman for
its part had at the time an ambitious but short reigning CEO would had dreams of expanding
the company into mech production. He would assign a team the task of looking over the design
of the Liberator and using it as a template to produce a new mech. However, he would be
replaced two years later and while the "Liberator II" project would continue it would be
shunted off to a lower prioritization. 57 years would pass with the project going through
various shut downs, starts ups, redesign's, fixes, and updates. Until 3146 when the Ari
Humphrey's caught wind of the project. Looking to 'flex' the muscle of the Duchy of
Andurien, he would investigate into Grumman's "Liberator II" project. Approving of what he
found, he would apply political pressure to the company to 1) prioritize the mech for
construction and production and two 2) rechristen it to the Catherine after the (in)famous
former Duchess who had bravely asserted Andurien Independence. 5 Years later the Catherine
CTE-1A would officially roll off the Assembly line (with state support to complete
production facilities.) The new domestically produced mech would be intended to fill the
role of being a scout, skirmisher/harasser, garrison mech, and line-filler. Only time would
tell if the Duchy of Andurien would find success in the design.
Capabilities:
The 45ton design would come equipped with 270 rated XL engine allowing the mech to hit
speeds of 97 km/h. Additionally, 5 jump-jets would be installed allowing the CTE-1 to jump
up to 150 meters. For armament the Catherine CTE-1A would come equipped with a Large X-pulse
laser in the left torso and an LRM-10 in the right. The LRM would be supplied with a single
ton of ammo protected by CASE II. This would be rounded out with an er-medium laser
installed into the center torso and an X-pulse small laser installed into the head. 8.5 tons
of Light Ferro-Fibrous armor would be used to protect the mech and 12 double heatsinks would
keep it cool. Special Note: Design Quriks: Extended Torso Twist.
================================================================================================
Equipment Mass
------------------------------------------------------------------------------------------------
Internal Structure: Endo Steel 2.50
Engine: 270 XL 7.50
Walking MP: 6
Running MP: 9
Jumping MP: 5
Heat Sinks (Double): 12 [24] 2.00
Gyro: Standard 3.00
Cockpit: Standard 3.00
Armor Factor: 144 8.50
Type: Light Ferro-Fibrous
Internal Armor
Structure Value
Head: 3 9
Center Torso: 14 20
Center Torso (rear): 5
R/L Torso: 11 16
R/L Torso (rear): 5
R/L Arm: 7 14
R/L Leg: 11 20
================================================================================================
Weapons and Ammo Location Critical Tonnage
------------------------------------------------------------------------------------------------
Small X-Pulse Laser H 1 1.00
ER Medium Laser CT 1 1.00
Jump Jet CT 1 0.50
CASE II RT 1 1.00
Jump Jet RT 1 0.50
LRM 10 RT 2 5.00
LRM 10 (Ammo 12) RT 1 1.00
Jump Jet LT 1 0.50
Large X-Pulse Laser LT 2 7.00
Jump Jet RL 1 0.50
Jump Jet LL 1 0.50
================================================================================================
Alpha Strike Statistics
------------------------------------------------------------------------------------------------
Point Value (PV): 31
TP: BM, SZ: 2, TMM: 2, MV: 12"/10"j
Damage: (S) 2 / (M) 3 / (L) 1, OV: 0
Armor (A): 5, Structure (S): 2
Specials: CASEII, IF1
|
|
|
Back to top |
|
Vagabond Mercenary Mr. Referee
Joined: 04-Feb-2002 00:00 Posts: 5789 Location: United States
|
Posted: 04-Dec-2023 20:08 Post subject: Catherine CTE-1A |
|
|
This is crazy to suggest, but after viewing the other designs, this might actually be a design that could benefit from a MRM/10 w/ Apollo FCS w/ 1t ammo. Removes the minimum range (at loss of range) and frees up 1t of weight. Upgrade the ER ML to X-MPL? _________________ one must work hard to cultivate the mind and body. and one must always cultivate the mind.
//^(^_^)^\\
|
|
Back to top |
|
Toxic_Toast Free Worlds League Sergeant
Joined: 25-Aug-2023 21:49 Posts: 99 Location: United States
|
Posted: 04-Dec-2023 21:27 Post subject: Catherine CTE-1A |
|
|
Hmmmmm I'll take it under consideration 🤔, seems interesting
|
|
Back to top |
|
|
|
» |
All times are GMT-05:00 |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
|
|
|
|